Assessment of Martensitic Transformation Paths Based on Transformation Potential Calculations [0.03%]
基于转变势计算的马氏体转变路径评估方法研究
Adam Creuziger,Whitney A Poling,Thomas Gnaeupel-Herold
Adam Creuziger
Transformation potentials for two different martensitic transformation paths are calculated and compared to experimentally measured austenite textures of an SAE 201 stainless steel. The authors conclude that the γ → ε → α' transformati...
Deformation Behavior and Damage Evaluation in a New Titanium Diboride (TiB2) Steel-Based Composite [0.03%]
新型二硼化钛（TiB2）钢基复合材料的变形行为和损伤评估
Zehoua Hadjem-Hamouche; Jean-Pierre Chevalier; Yiting Cui; Frédéric Bonnet
Zehoua Hadjem-Hamouche; Jean-Pierre Chevalier; Yiting Cui; Frédéric Bonnet
On the Cyclic Softening Mechanisms of Reduced Activity Ferritic/Martensitic Steels [0.03%]
低活性铁素体/马氏体钢循环软化机理研究
Maria Florencia Giordana; Iris Alvarez-Armas; Alberto Armas
Maria Florencia Giordana; Iris Alvarez-Armas; Alberto Armas
Reduction of CO2 Emissions from Steel Plants by Using Steelmaking Slags for Production of Marketable Calcium Carbonate [0.03%]
利用炼钢渣生产可销售的碳酸钙减少钢铁厂的二氧化碳排放
Sanni Eloneva; Sebastian Teir; Hannu Revitzer; Justin Salminen; Arshe Said; Carl-Johan Fogelholm; Ron Zevenhoven
Sanni Eloneva; Sebastian Teir; Hannu Revitzer; Justin Salminen; Arshe Said; Carl-Johan Fogelholm; Ron Zevenhoven
F. Nürnberger; O. Grydin; Z. Yu; M. Schaper; Fr.-W. Bach
F. Nürnberger; O. Grydin; Z. Yu; M. Schaper; Fr.-W. Bach
Operation at High Pellet Ratio and Without External Slag Formers – Trials in an Experimental Blast Furnace [0.03%]
在高球团比和无外部造渣机的情况下运行——在实验高炉中的试验
Nicklas Eklund; Bo Lindblom; Jan-Olov Wikström; Bo Björkman
Nicklas Eklund; Bo Lindblom; Jan-Olov Wikström; Bo Björkman
EAF Smelting Trials of Waste-Carbon Briquettes at Avesta Works of Outokumpu Stainless AB for Recycling Oily Mill Scale Sludge from Stainless Steel Production [0.03%]
奥托昆普不锈钢有限公司阿维斯塔工厂废碳砖电弧炉冶炼试验，用于回收不锈钢生产中的含油氧化皮污泥
Qixing Yang; Nils Holmberg; Bo Björkman
Qixing Yang; Nils Holmberg; Bo Björkman
Spray Cooling Heat Transfer and Calculation of Water Impact Density for Cooling of Steel Sheet Materials by Inverse Process Modelling [0.03%]
通过逆过程模型计算钢板材料冷却的喷雾冷却传热和水冲击密度
J. Wendelstorf; R. Wendelstorf; K.-H. Spitzer
J. Wendelstorf; R. Wendelstorf; K.-H. Spitzer
Mika Järvinen; Aki Kärnä; Timo Fabritius
Mika Järvinen; Aki Kärnä; Timo Fabritius
Prevention of Internal Cracks in Forward Extrusion by Means of Counter Pressure: A Numerical Treatise [0.03%]
用反压法防止正向挤压中的内部裂纹：一篇数值论文
C. Soyarslan; A. E. Tekkaya
C. Soyarslan; A. E. Tekkaya