Improving the Accuracy of Dental Impressions: A Study of Tray Adjustments and Materials [0.03%]
改进牙模精度：关于牙模调整和材料的研究
S Naidu,P Dhawan,S Raman
S Naidu
Objectives: This study evaluated the tensile bond strength of addition silicone impression material when used with custom trays featuring grooves and perforations, made from self-cure acrylic resin, visible light-cure (VL...
Description and Durability of the Various Direct Restoration Techniques in Molar-Incisor Hypomineralization: A Systematic Review [0.03%]
乳牙低矿化症各种直接修复技术的描述和耐久性：系统评价
R Denis,M Marty,R Esclassan et al.
R Denis et al.
Introduction: Molar-incisor hypomineralization (MIH) is a qualitative defect of the enamel structure affecting at least one of the first permanent molars. Treatment will depend on its severity, the stage of dental develop...
Does the Learning Curve for Intraoral Scanning Vary Depending on the Device? [0.03%]
用于口腔内扫描的设备学习曲线是否有所不同？
M S N Borges,L Cardoso,M T Rea et al.
M S N Borges et al.
Objectives: Digital impressions using intraoral scanners (IOS) are replacing conventional impressions, requiring a learning process. This study compared the learning curves of 29 dentists with no prior IOS experience, ran...
Accuracy of Intra-Oral Scanners for Full Crown Tooth Preparations with Subgingival Margins: A Systematic Review [0.03%]
含牙龈下边缘全冠预备体的口内扫描仪准确性系统评价
M Andrade Villalobos,V Bennani,J M Aarts et al.
M Andrade Villalobos et al.
Introduction: The accuracy of intra-oral scanners (IOS) has not been thoroughly evaluated across all clinical scenarios, particularly in crown preparations with subgingival margins. ...
Performance of Fiberglass Posts Versus Fiber- Reinforced Resin Composites in Endodontically Treated Anterior Teeth Without Ferrule: A Systematic Review [0.03%]
无牙本质肩领的前牙根管治疗后玻璃纤维桩与纤维增强树脂核的临床疗效：一项系统评价
S K Guzmán Reyes,D E Brito Bojorque,J F Calle Prado et al.
S K Guzmán Reyes et al.
Objective: To perform a systematic review of in vitro studies examining endodontically treated anterior teeth restored with fiberglass posts versus composite posts reinforced with: polyethylene fibers (Ribbond), fiber-rei...
Influence of Surface Roughness on the Adhesion of Hydroxyapatite Coatings to Titanium and Titanium Alloy Surfaces: A Systematic Review of in vitro Experimental Studies [0.03%]
羟基磷灰石涂层与钛及钛合金表面黏附性能的体内实验研究系统评价：体外实验研究系统评价：表面粗糙度的影响
V de Melo-Soares,I Gazott-Simões,A C Dos Reis et al.
V de Melo-Soares et al.
This systematic review gathered evidence to identify the influence of roughness on titanium surfaces on the adhesion of hydroxyapatite coatings. This research followed the PRISMA guidelines and was registered on the Open Science Framework (...
Editorial: A Journal with a Vision into the Evolution of the Dental Profession [0.03%]
展望口腔医学的发展——一篇有远见的述评文章
M Özcan
M Özcan
I would like to greet you all as the incoming Editor-in-Chief of the European Journal of Prosthodontics and Restorative Dentistry (EJPRD) which has a history of over 60 years. Back in 1965, the journal was initially named 'Journal (Anglo-Co...
Assessment of Efficacy of Implant Screwdrivers' During Multiple Tightening/ Untightening Cycles. An in vitro Study [0.03%]
种植体扭矩扳手多次扭紧/松开循环的效能评价-一项离体研究
R Batista,A Moreira,N Alves et al.
R Batista et al.
Introduction: It is unclear the number of times a screwdriver may be reused without loosening its efficacy or inducing damage to implant screws while keeping appropriate torque values. ...
Hybrid Full-Arch Rehabilitation Using Conventional And Zygomatic Implants: A Short-Term Retrospective Analysis [0.03%]
传统与zygoma种植体混合全口重建的短期回顾性分析
T Grandi,P Toti,U Covani et al.
T Grandi et al.
Objectives: To report one-year outcomes of prosthetic rehabilitation of the atrophic maxillae, supported by angled abutments on zygomatic implants and conventional implants. ...
Effect of Surface Treatments on the Bond Strength of Computer-aided Design and Computer-aided Manufacturing Lithium Disilicate to Restorative Materials: A Systematic Review [0.03%]
表面处理对计算机辅助设计和制造锂二硅酸盐与修复材料粘结强度的影响：一项系统评价
R Shoorgashti,S S Ehsani,M Ducret et al.
R Shoorgashti et al.
Objectives: Using computer-aided design and manufacturing (CAD-CAM) technology in restorative dentistry increased the application of lithium disilicate (LD) materials. The bond strength to core and repairing materials is ...