Siemon De Nys,Marko Turkalj,Radu Corneliu Duca et al.
Siemon De Nys et al.
Objectives: Resin composites may release bisphenol A (BPA) due to impurities present in the monomers. However, there is a lack of knowledge regarding the leaching characteristics of BPA from resin composites. Therefore, e...
Conventional sintering of nano-crystalline Yttria-Stabilized Zirconia enables high-strength, highly translucent and opalescent dental ceramics [0.03%]
传统烧结法制备的纳米晶氧化钇稳定的四方相氧化锆牙用陶瓷具有高强度、高透明度和浑浊效应
Omid Akhlaghi,Erik Camposilvan,Vincent Garnier et al.
Omid Akhlaghi et al.
Development of restorative materials capable of mimicking optical and mechanical performance of natural teeth is a quest in aesthetic density. Yttria-Stabilized Zirconia (YSZ) ceramics represent one of the most popular choices for dental re...
Influence of different pre-treatments on the resin infiltration depth into enamel of teeth affected by molar-incisor hypomineralization (MIH) [0.03%]
不同预处理对乳牙酸蚀封闭深度影响的实验研究
Stefanie Amend,Stephan Stork,Susanne Lücker et al.
Stefanie Amend et al.
Objectives: This in vitro pilot study aimed to evaluate whether different pre-treatments (demineralization, deproteinization, (chemo-)mechanical reduction of the surface layer) influence the penetration depth of a resin i...
Effects of printing orientation and artificial ageing on martens hardness and indentation modulus of 3D printed restorative resin materials [0.03%]
打印方向和人工老化对3D打印修复树脂材料马氏硬度及压痕模量的影响
Shaymaa Mudhaffer,Rana Althagafi,Julfikar Haider et al.
Shaymaa Mudhaffer et al.
Background: Three-dimensional (3D) printing is increasingly used to fabricate dental restorations due to its enhanced precision, consistency and time and cost-saving advantages. The properties of 3D-printed resin material...
Effect of polymerisation protocols on water sorption, solubility and hygroscopic expansion of fast-cure bulk-fill composite [0.03%]
聚合工艺对快速固化充填复合材料吸水性、溶解性和吸湿膨胀的影响
Halah Thanoon,Nikolaos Silikas,David C Watts
Halah Thanoon
Objective: This study examines the effect of two light-curing protocols from a LED polywave light curing unit (LCU) on water sorption, solubility, and hygroscopic expansion of fast and conventional bulk-fill resin-based c...
Do strength of zirconia-abutment-interfaces depend on cement, zirconia type and titanium abutment dimensions? [0.03%]
基台类型、钛质基台尺寸及粘接剂对锆基台连接强度的影响研究
Zumreta Alic,Tom Vaskovich,Alexander Franz et al.
Zumreta Alic et al.
Objectives: Part 1 of this study investigates the influence of zirconia types, chimney heights, and gingival heights on the strength of the zirconia-abutment-interface. Part 2 extends the analysis to include adhesive bran...
Assessments of polymerization shrinkage by optical coherence tomography-based digital image correlation analysis-Part I: Parameter identification [0.03%]
基于光学相干层析成像的数字图像相关法分析充填材料聚合收缩应力的研究（第I部分）：参数识别
Wei-Chi Chen,Shu-Fen Chuang,Po-Chun Tseng et al.
Wei-Chi Chen et al.
Objective: To investigate the feasibility of optical coherence tomography (OCT)-based digital image correlation (DIC) analysis and to identify the experimental parameters for measurements of polymerization shrinkage. ...
Multi-acrylamides improve bond stability through collagen reinforcement under physiological conditions [0.03%]
多丙烯酰胺通过生理条件下胶原增强改善粘结稳定性
Lincoln Borges,Matthew Logan,Samuel Weber et al.
Lincoln Borges et al.
Objectives: Acrylamides were shown to significantly improve bonding stability in adhesive restorations, but the reinforcement mechanism has not been fully elucidated. We tested the hypothesis that hydrogen bonding reinfor...
Photopolymerizable semi-crystalline polymers for thermally reversible, 3D printable cast molds [0.03%]
可用于热可逆、三维打印铸件模具的光固化半结晶聚合物
Rachel Becker,Alexa S Kuenstler,Christopher N Bowman
Rachel Becker
Objectives: This study demonstrates the use of photopolymerization to create semi-crystalline linear polymers suitable for thermally reversible materials in dental cast moldings produced from 3D printing. ...
Microstructural investigation of hybrid CAD/CAM restorative dental materials by micro-CT and SEM [0.03%]
微 computed tomography 和扫描电子显微镜下混合计算机辅助设计和制造的修复体材料的微观结构研究
Elisabeth Prause,Jeremias Hey,Florian Beuer et al.
Elisabeth Prause et al.
Objectives: An increasing number of CAD/CAM (computer-aided design/computer-aided manufacturing) hybrid materials have been introduced to the dental market in recent years. In addition, CAD/CAM hybrid materials for additi...