Kinetic analysis of MgB2 layer formation in advanced internal magnesium infiltration (AIMI) processed MgB2 wires [0.03%]
先进内部镁浸渗(AIMI)工艺制备MgB2线材中MgB2层生长动力学分析
G Z Li,M D Sumption,E W Collings
G Z Li
Significantly enhanced critical current density (Jc) for MgB2 superconducting wires can be obtained following the advanced internal Mg infiltration (AIMI) route. But unless suitable precautions are taken, the AIMI-processed MgB2 wires will ...
The influence of a brittle Cr interlayer on the deformation behavior of thin Cu films on flexible substrates: Experiment and model [0.03%]
脆性铬中间层对柔性基底上薄铜膜变形行为的影响：实验与模型
Vera M Marx,Florian Toth,Andreas Wiesinger et al.
Vera M Marx et al.
Thin metal films deposited on polymer substrates are used in flexible electronic devices such as flexible displays or printed memories. They are often fabricated as complicated multilayer structures. Understanding the mechanical behavior of...
R Hollerweger,D Holec,J Paulitsch et al.
R Hollerweger et al.
The complex structure of Ta2O5 led to the development of various structural models. Among them, superstructures represent the most stable configurations. However, their formation requires kinetic activity and long-range ordering processes, ...
Direct evidence for grain boundary motion as the dominant restoration mechanism in the steady-state regime of extremely cold-rolled copper [0.03%]
极冷铜带恒定轧制状态下晶界迁移为主要再结晶机制的直接证据
O Renk,A Hohenwarter,S Wurster et al.
O Renk et al.
Ultra-fine-grained high-purity copper (99.99%) deformed by means of high-pressure torsion into the steady-state regime was subjected to additional rolling deformation. The microstructural changes as a function of the applied strain were ana...
Grain boundary excess volume and defect annealing of copper after high-pressure torsion [0.03%]
高压扭转会后铜的晶界过剩体积及缺陷的退火过程
Bernd Oberdorfer,Daria Setman,Eva-Maria Steyskal et al.
Bernd Oberdorfer et al.
The release of excess volume upon recrystallization of ultrafine-grained Cu deformed by high-pressure torsion (HPT) was studied by means of the direct technique of high-precision difference dilatometry in combination with differential scann...
Hydrogels in Healthcare: From Static to Dynamic Material Microenvironments [0.03%]
用于医疗保健的水凝胶：从静态到动态材料微环境
Chelsea M Kirschner,Kristi S Anseth
Chelsea M Kirschner
Advances in hydrogel design have revolutionized the way biomaterials are applied to address biomedical needs. Hydrogels were introduced in medicine over 50 years ago and have evolved from static, bioinert materials to dynamic, bioactive mic...
Exsolution by spinodal decomposition in multicomponent mineral solutions [0.03%]
多组分矿物溶液中通过自旋odb82a6分解的解出作用
E Petrishcheva,R Abart
E Petrishcheva
Phase separation in a three-component system that results from the uphill diffusion of chemical components is considered. The binary decomposition model of Cahn and Hilliard is generalized to account for the interdiffusion of several chemic...
Fracture of ECAP-deformed iron and the role of extrinsic toughening mechanisms [0.03%]
ECAP变形铁的断裂及外生增韧机理的作用
A Hohenwarter,R Pippan
A Hohenwarter
The fracture behaviour of pure iron deformed by equal-channel angular pressing via route A was examined. The fracture toughness was determined for different specimen orientations and measured in terms of the critical plane strain fracture t...
Detailed modelling of delamination buckling of thin films under global tension [0.03%]
全球拉伸下薄膜层开裂起皱的详细模型分析
F Toth,F G Rammerstorfer,M J Cordill et al.
F Toth et al.
Tensile specimens of metal films on compliant substrates are widely used for determining interfacial properties. These properties are identified by the comparison of experimentally observed delamination buckling and a mathematical model whi...
Temperature driven evolution of thermal, electrical, and optical properties of Ti-Al-N coatings [0.03%]
Ti-Al-N涂层的热、电和光性能的温度依赖性演变规律
Richard Rachbauer,Jamie J Gengler,Andrey A Voevodin et al.
Richard Rachbauer et al.
Monolithic single phase cubic (c) Ti1-x Al x N thin films are used in various industrial applications due to their high thermal stability, which beneficially effects lifetime and performance of cutting and milling tools, but also find incre...